Hi,
I am playing around with latest 2014.2 - Designer for WPF - Chart editor - Line series. To me it looks like its bit buggy for the Interaction and Label sections.
For example in the attached example I have enabled the properties under Interaction section and specified the Tool tip column but you will notice following:
1. Its not able to show me the tool tip.
2. Also when I hover for the legend values its not highlighting the entire corresponding line.
3. If I check the drill down enabled property - it has no effect - Infact if I close the report.mrt and open it again - this property is unchecked.
4. After this if you uncheck all off the properties in Interaction section, it has no effect - means hovering over marker still highlights the marker.
Also, the Labels - from Chart and from Series is bit ambiguous.
For example if you add another Clustered Column chart (bar chart) with similar configuration in the same report then its quite hard to set labels - try setting it to None in one chart and Outside end in the another chart - you won't be able to do it.
Could you please have a look at it, may be I am missing something.
Thanks,
Sandeep
Buggy Chart editor (in Designer for WPF) for 2014.2
Buggy Chart editor (in Designer for WPF) for 2014.2
- Attachments
-
- ToolTip_data.csv
- Sample data
- (547 Bytes) Downloaded 187 times
-
- BuggyDesignerReport.mrt
- Report template
- (13.24 KiB) Downloaded 187 times
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hello.
Sorry, for delay with answer. We need some additional time for analyzing of all issues.
We will let you know about results.
Thank you.
Sorry, for delay with answer. We need some additional time for analyzing of all issues.
We will let you know about results.
Thank you.
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hello,
We made some fixes in this direction.
Please check the next prerelease build which will be available on this week.
Thank you.
We made some fixes in this direction.
Please check the next prerelease build which will be available on this week.
Thank you.
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hi Aleksey,
I checked on pre-release 2014.2.2001 build - the Drill Down enabled property is working as expected.
I noticed that the ResetPageNumber property on a Page - if you set it to True by using designer - it doesn't get saved (You need to open and close the report to see it)
Thanks,
Sandeep
I checked on pre-release 2014.2.2001 build - the Drill Down enabled property is working as expected.
I noticed that the ResetPageNumber property on a Page - if you set it to True by using designer - it doesn't get saved (You need to open and close the report to see it)
Thanks,
Sandeep
Last edited by sandynith on Sun Nov 02, 2014 8:29 pm, edited 1 time in total.
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hello, Sandeep.
Please, send us more detailed description of problem with Drill-down and we can reproduce the issue with ResetPageNumber.
Please, send us a sample report template with step-by-step instruction.
Thank you.
Please, send us more detailed description of problem with Drill-down and we can reproduce the issue with ResetPageNumber.
Please, send us a sample report template with step-by-step instruction.
Thank you.
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hi Aleksey,
I am sorry for typing it wrong, what I meant to say is:
The Drill Down property is working fine now in 2014.2.2001..its good (updated my previous post as well)
ResetPageNumber - If you set it to True by using designer - it does not get saved. I think you are able to reproduce this issue.
Cheers,
Sandeep
I am sorry for typing it wrong, what I meant to say is:
The Drill Down property is working fine now in 2014.2.2001..its good (updated my previous post as well)
ResetPageNumber - If you set it to True by using designer - it does not get saved. I think you are able to reproduce this issue.
Cheers,
Sandeep
Re: Buggy Chart editor (in Designer for WPF) for 2014.2
Hello, Sandeep.
Where do you set the Reset Page Number property?
Please, send us step-by-step instruction or video where we could see how to reproduce the issue.
Thank you.
Sorry, but we couldn't reproduce this issue.sandynith wrote:ResetPageNumber - If you set it to True by using designer - it does not get saved. I think you are able to reproduce this issue.
Where do you set the Reset Page Number property?
Please, send us step-by-step instruction or video where we could see how to reproduce the issue.
Thank you.