Bleed Settings ?
-
- Posts: 85
- Joined: Sat Jan 20, 2007 4:21 am
Bleed Settings ?
Hi,
i have following print requirements
1.0.25 inch bleed
2.Crop marks, offset 30 pt (.4167 inch)
3.Final print size after cuts is 8 3/8" x 10 7/8" built as 8 ½” x 11”
Please tell, how to set this requirements in template?
Thanks in advance,
Jayakumar
i have following print requirements
1.0.25 inch bleed
2.Crop marks, offset 30 pt (.4167 inch)
3.Final print size after cuts is 8 3/8" x 10 7/8" built as 8 ½” x 11”
Please tell, how to set this requirements in template?
Thanks in advance,
Jayakumar
Bleed Settings ?
Hi Jayakumar,
Do you print from Dot matrix mode?
Thank you.
Do you print from Dot matrix mode?
Thank you.
-
- Posts: 85
- Joined: Sat Jan 20, 2007 4:21 am
Bleed Settings ?
Hi Edward,
No.We are using Plateprinting CTP printers.
Regards,
Jayakumar
No.We are using Plateprinting CTP printers.
Regards,
Jayakumar
Bleed Settings ?
Have you tried to double click the page in the designer and to set the required margins and page height and width?
Which problems have you faced?
Thank you.
Which problems have you faced?
Thank you.
-
- Posts: 85
- Joined: Sat Jan 20, 2007 4:21 am
Bleed Settings ?
Hi Edward,
There is no problem in margin settings and page width and height.i don't know how to set the bleed(previous post requirements) using those margins and page width and height.
Please help me to solve the requirements.
Thanks in advance,
Jayakumar
There is no problem in margin settings and page width and height.i don't know how to set the bleed(previous post requirements) using those margins and page width and height.
Please help me to solve the requirements.
Thanks in advance,
Jayakumar
-
- Posts: 85
- Joined: Sat Jan 20, 2007 4:21 am
Bleed Settings ?
Hi Edward,
Have you found the solution ? if you found then please reply me.
Regards,
Jayakumar
Have you found the solution ? if you found then please reply me.
Regards,
Jayakumar
Bleed Settings ?
Hello,
Can you explain what is "previous post requirements" ?
Thank you.
Can you explain what is "previous post requirements" ?
Thank you.
-
- Posts: 85
- Joined: Sat Jan 20, 2007 4:21 am
Bleed Settings ?
Hi,
i have following print requirements
1.0.25 inch bleed
2.Crop marks, offset 30 pt (.4167 inch)
3.Final print size after cuts is 8 3/8" x 10 7/8" built as 8 ½” x 11”
Please tell, how to set this requirements in template?
Thanks in advance,
Jayakumar
---------------------------------
Hi Edward,
No.We are using Plateprinting CTP printers.
Regards,
Jayakumar
-----------------------------------
Hi Edward,
There is no problem in margin settings and page width and height.i don't know how to set the bleed(previous post requirements) using those margins and page width and height.
Please help me to solve the requirements.
Thanks in advance,
Jayakumar
i have following print requirements
1.0.25 inch bleed
2.Crop marks, offset 30 pt (.4167 inch)
3.Final print size after cuts is 8 3/8" x 10 7/8" built as 8 ½” x 11”
Please tell, how to set this requirements in template?
Thanks in advance,
Jayakumar
---------------------------------
Hi Edward,
No.We are using Plateprinting CTP printers.
Regards,
Jayakumar
-----------------------------------
Hi Edward,
There is no problem in margin settings and page width and height.i don't know how to set the bleed(previous post requirements) using those margins and page width and height.
Please help me to solve the requirements.
Thanks in advance,
Jayakumar
Bleed Settings ?
Hi Jayakumar,
Our report generator can set the magins of printing, type of paper, paper size.
All other settings you may setup manually using components of the report generator (bands etc)
Thank you.
Our report generator can set the magins of printing, type of paper, paper size.
All other settings you may setup manually using components of the report generator (bands etc)
Thank you.