Change control height in before print

Stimulsoft Reports.WEB discussion
nemanja.avramovic
Posts: 17
Joined: Wed Jul 11, 2012 11:41 am

Re: Change control height in before print

Post by nemanja.avramovic »

Thank you, you are kind.
HighAley
Posts: 8430
Joined: Wed Jun 08, 2011 7:40 am
Location: Stimulsoft Office

Re: Change control height in before print

Post by HighAley »

Hello.

We are always glad to help you.
Let us know if you need any additional help.

Thank you.
nemanja.avramovic
Posts: 17
Joined: Wed Jul 11, 2012 11:41 am

Re: Change control height in before print

Post by nemanja.avramovic »

Hi,
since you mentioned additional help, I am not sure if my requests were clear enough.
So I prepared testReport with data backup (mssql db) for you. This is the concrete scenario where I need your help.
This may help you in your analysis for problem reproduction and making solution.

Best regards!
Attachments
FixHeightInSubreportTrashData.7z
Report dataBase.
(83.16 KiB) Downloaded 259 times
FixHeightInSubreportTrashData.mrt
Report file.
(32.47 KiB) Downloaded 299 times
HighAley
Posts: 8430
Joined: Wed Jun 08, 2011 7:40 am
Location: Stimulsoft Office

Re: Change control height in before print

Post by HighAley »

Hello.

We avoid the use of sub-report.
Please, look at the attached report template.
FixHeightInSubreportTrashData_modified.mrt
(30.74 KiB) Downloaded 397 times
Thank you.
nemanja.avramovic
Posts: 17
Joined: Wed Jul 11, 2012 11:41 am

Re: Change control height in before print

Post by nemanja.avramovic »

Thank you very much!
This is a great solution and simplification in one.
I was convinced that Subreport was necessary for relation binding on CrossTab.
Perhaps, Subreports are for relating only among DataBands.

I am satisfied, this topic has the good ending.
The only thing that remained mystery for me are report events on controls: Before print, After print, Get value, Get tag, and so on...
I was looking in Stimulsoft_Reports_Manual.En.pdf and had not found anything about it.
Can you, please, refer me where I can learn more about them, when they occur, how many times, and what arguments are available?

Thanks again, and best regards!
HighAley
Posts: 8430
Joined: Wed Jun 08, 2011 7:40 am
Location: Stimulsoft Office

Re: Change control height in before print

Post by HighAley »

Hello.
nemanja.avramovic wrote:Thank you very much!
This is a great solution and simplification in one.
I was convinced that Subreport was necessary for relation binding on CrossTab.
Perhaps, Subreports are for relating only among DataBands.
There are several bands could be on the one page so it's better to avoid using sub-reports.
nemanja.avramovic wrote:I am satisfied, this topic has the good ending.
The only thing that remained mystery for me are report events on controls: Before print, After print, Get value, Get tag, and so on...
I was looking in Stimulsoft_Reports_Manual.En.pdf and had not found anything about it.
Can you, please, refer me where I can learn more about them, when they occur, how many times, and what arguments are available?
We are working on our documentation permanently. We will add a chapter about events in our next release.

Thank you.
nemanja.avramovic
Posts: 17
Joined: Wed Jul 11, 2012 11:41 am

Re: Change control height in before print

Post by nemanja.avramovic »

That's great!
Thanks for answers.
HighAley
Posts: 8430
Joined: Wed Jun 08, 2011 7:40 am
Location: Stimulsoft Office

Re: Change control height in before print

Post by HighAley »

Hello.

We are always glad to help you.

Thank you.
Post Reply