Cross Tab - DataBand
-
- Posts: 219
- Joined: Tue Oct 27, 2015 4:19 pm
Cross Tab - DataBand
Hello.
When I put the crosstab in a DataBand is not printed PageHeaderBand on the next page. See attached example, page 5:
Thank you.
When I put the crosstab in a DataBand is not printed PageHeaderBand on the next page. See attached example, page 5:
Thank you.
- Attachments
-
- CrossTabOnDataBand - Cópia.mrt
- (33.09 KiB) Downloaded 398 times
-
- Cross-Tab on DataBand.pdf
- (2.34 MiB) Downloaded 563 times
Re: Cross Tab - DataBand
Hello, Leandro.
This is not a page, but a segment of the page.
It is created when a Cross-tab is larger than the page.
You could use a solution from the attached report template.
Thank you
This is not a page, but a segment of the page.
It is created when a Cross-tab is larger than the page.
You could use a solution from the attached report template.
Thank you
- Attachments
-
- UnlimitedWidthWithPageHeadersAndFooters.mrt
- (26.41 KiB) Downloaded 527 times
-
- Posts: 219
- Joined: Tue Oct 27, 2015 4:19 pm
Re: Cross Tab - DataBand
Hello.
I did not understand. The example does not have the crosstab component.
Thank you.
I did not understand. The example does not have the crosstab component.
Thank you.
Re: Cross Tab - DataBand
Hello, Leandro.
In this example the same page segments are created.
You could find out how to shoe the Headers and Footers on the segments there.
Thank you.
In this example the same page segments are created.
You could find out how to shoe the Headers and Footers on the segments there.
Thank you.
-
- Posts: 219
- Joined: Tue Oct 27, 2015 4:19 pm
Re: Cross Tab - DataBand
Hello.
PagesCount It is a variable. What would it be RenderedPages[0].SegmentPerWidth and IsFirstPass?
I can use a DataBand instead of using ReportTitleBand?
Thank you.
PagesCount It is a variable. What would it be RenderedPages[0].SegmentPerWidth and IsFirstPass?
I can use a DataBand instead of using ReportTitleBand?
Thank you.
Re: Cross Tab - DataBand
Hello, Leandro.
The RenderedPages[0].SegmentPerWidth is a number of segments of the rendered page.
You should get it to know how many segments is on the page.
The IsFirstPass is a system variable that shows that it is the first pass.
It possible to change the Number of Pass property of the report to Double pass. In this case the report will be rendered two times.
You could get some information on the first pass and make chenge on the second (IsSecondPass).
Thank you.
The RenderedPages[0].SegmentPerWidth is a number of segments of the rendered page.
You should get it to know how many segments is on the page.
The IsFirstPass is a system variable that shows that it is the first pass.
It possible to change the Number of Pass property of the report to Double pass. In this case the report will be rendered two times.
You could get some information on the first pass and make chenge on the second (IsSecondPass).
Thank you.
-
- Posts: 219
- Joined: Tue Oct 27, 2015 4:19 pm
Re: Cross Tab - DataBand
Hello.
Got it. Because I have to switch to double-pass?
I can use a DataBand instead of using ReportTitleBand?
Thank you.
Got it. Because I have to switch to double-pass?
I can use a DataBand instead of using ReportTitleBand?
Thank you.
Re: Cross Tab - DataBand
Hello.
Yes, you should switch to the Double Pass.
Yes, you could use the Data Band.
Thank you.
Yes, you should switch to the Double Pass.
Yes, you could use the Data Band.
Thank you.
-
- Posts: 219
- Joined: Tue Oct 27, 2015 4:19 pm
Re: Cross Tab - DataBand
Hello.
But if I switch to Double Pass the report will run twice and will get very slow.
Please could send me an example using Data Band because it did not work.
Thank you.
But if I switch to Double Pass the report will run twice and will get very slow.
Please could send me an example using Data Band because it did not work.
Thank you.
Re: Cross Tab - DataBand
Hello,
In any cases, for this task, you should use Double Pass.
Thank you.
In any cases, for this task, you should use Double Pass.
Thank you.