Change control height in before print
-
- Posts: 17
- Joined: Wed Jul 11, 2012 11:41 am
Re: Change control height in before print
Thank you, you are kind.
Re: Change control height in before print
Hello.
We are always glad to help you.
Let us know if you need any additional help.
Thank you.
We are always glad to help you.
Let us know if you need any additional help.
Thank you.
-
- Posts: 17
- Joined: Wed Jul 11, 2012 11:41 am
Re: Change control height in before print
Hi,
since you mentioned additional help, I am not sure if my requests were clear enough.
So I prepared testReport with data backup (mssql db) for you. This is the concrete scenario where I need your help.
This may help you in your analysis for problem reproduction and making solution.
Best regards!
since you mentioned additional help, I am not sure if my requests were clear enough.
So I prepared testReport with data backup (mssql db) for you. This is the concrete scenario where I need your help.
This may help you in your analysis for problem reproduction and making solution.
Best regards!
- Attachments
-
- FixHeightInSubreportTrashData.7z
- Report dataBase.
- (83.16 KiB) Downloaded 260 times
-
- FixHeightInSubreportTrashData.mrt
- Report file.
- (32.47 KiB) Downloaded 299 times
Re: Change control height in before print
Hello.
We avoid the use of sub-report.
Please, look at the attached report template. Thank you.
We avoid the use of sub-report.
Please, look at the attached report template. Thank you.
-
- Posts: 17
- Joined: Wed Jul 11, 2012 11:41 am
Re: Change control height in before print
Thank you very much!
This is a great solution and simplification in one.
I was convinced that Subreport was necessary for relation binding on CrossTab.
Perhaps, Subreports are for relating only among DataBands.
I am satisfied, this topic has the good ending.
The only thing that remained mystery for me are report events on controls: Before print, After print, Get value, Get tag, and so on...
I was looking in Stimulsoft_Reports_Manual.En.pdf and had not found anything about it.
Can you, please, refer me where I can learn more about them, when they occur, how many times, and what arguments are available?
Thanks again, and best regards!
This is a great solution and simplification in one.
I was convinced that Subreport was necessary for relation binding on CrossTab.
Perhaps, Subreports are for relating only among DataBands.
I am satisfied, this topic has the good ending.
The only thing that remained mystery for me are report events on controls: Before print, After print, Get value, Get tag, and so on...
I was looking in Stimulsoft_Reports_Manual.En.pdf and had not found anything about it.
Can you, please, refer me where I can learn more about them, when they occur, how many times, and what arguments are available?
Thanks again, and best regards!
Re: Change control height in before print
Hello.
Thank you.
There are several bands could be on the one page so it's better to avoid using sub-reports.nemanja.avramovic wrote:Thank you very much!
This is a great solution and simplification in one.
I was convinced that Subreport was necessary for relation binding on CrossTab.
Perhaps, Subreports are for relating only among DataBands.
We are working on our documentation permanently. We will add a chapter about events in our next release.nemanja.avramovic wrote:I am satisfied, this topic has the good ending.
The only thing that remained mystery for me are report events on controls: Before print, After print, Get value, Get tag, and so on...
I was looking in Stimulsoft_Reports_Manual.En.pdf and had not found anything about it.
Can you, please, refer me where I can learn more about them, when they occur, how many times, and what arguments are available?
Thank you.
-
- Posts: 17
- Joined: Wed Jul 11, 2012 11:41 am
Re: Change control height in before print
That's great!
Thanks for answers.
Thanks for answers.
Re: Change control height in before print
Hello.
We are always glad to help you.
Thank you.
We are always glad to help you.
Thank you.